All posts by admin

Safety use of Rotisserie

Rotisserie grilling is certainly one of the earliest techniques of cooking. To get Centuries, individuals have known that food cooked slowly by constant turning over a heating source offers flavor and tenderness that’s tough to coincide with almost any other cooking process. Rotisseries are constructed in a wide range of sizes which range from models in a position to adapt just a little poultry to big models utilized for roasting large primal cuts of beef or whole creatures for example as a whole pig rotisserie.

rotisserie

 

Safety when handling a rotisserie.

Just like any type of cooking, safety must be of chief It’s just a safe, dependable cooking method once the appropriate procedures are completed and the apparatus is used in line with the directions issued by the manufacturer. The hints given below must be followed closely to guarantee rotisserie grilling can be just a safe procedure. Some of the safety practices when handling rotisserie include;

  1. When utilizing gas grills built with automatic ignition, the Burners shouldn’t be lit while the hood is shut. This will reduce the likeliness of explosion.
  2. Make sure the power cable to the rotisserie unit doesn’t cross a very higher traffic location.
  3. Always keep outside grills using rotisserie attachments off out of the Walls of buildings and out of under low hanging tree branches in use.
  4. Ensure all the parts and gears needed for the rotisserie are available before start.
  5. Grills with rotisserie attachments Intended for outdoor usage Only.
  6. Many gas and gas grills involve rotisserie components or offer them as a substitute which may be used later. If a barbecue isn’t meant to adapt a rotisserie, never re configure it using homemade apparatus for the intended purpose of attempting rotisserie grilling.
  7. Grills with rotisserie attachments must be put within a Area that’s flat, like an outdoor terrace or designated lawn space. That really is The rotisserie unit works precisely.
  8. Children and pets must be kept off from the rotisserie living area.

These are some of the important measures you should take when using the rotisserie which is very common with the outdoor camping and expeditions.

Tips for Hiking with dogs

There’s nothing better than a furry friend by your side while hiking. Hiking with dogs can be highly rewarding. Are you ready to take on the challenge of bringing dog with you? Here are a few tips you need to keep in mind before you head out, such as safe expeditions, nutrition and etc.

The Ten Essentials

  1. ID Tags and photo identification

ID tag is a plastic or metal medallion that hangs from your pup’s collar, lists specific contact information that will reunite you with your dog should she run off. For safety reasons, list only their name and phone number with no information about the dog. At the very least, list your name and the best way to contact you, whether it is a cell phone, office phone, or home phone.

Also, have a recent photo of your puppy on hand so you can show to others what he/she looks like.

Poop bags

Poop bags are beneficial to save our earth from pollution. You should always buy high quality bags that protect your atmosphere for long time. If trails permit, you can also bury waste in a hole away from water sources.

Obedience training

Are they obedient and well-socialized enough to make a good trail dog? Bring your dog hiking only if they are a breed suited to long walks. You should make sure that your dog will come to your side when called and also they can trust and listen you when facing with other hikers or wildlife. It is essential for your hiking when company with your puppy. Also you need to think about if your dog fit enough for the planned hike.

Dog backpack

Since you’re carrying the necessities, why not give your dog a backpack! Fill their backpack with some of their belongings to get them used to carrying something.

However, you should pay special attention on your dog seeing if your little one running into trouble, exhausting or overheating. If your dog is exhibiting signs of heat exhaustion, try to keep them as cool as possible until you can get them to the vet. If your dog is new to hiking, it’s best to check with your vet and then start small, with short hikes on easy trails. If there’s a difficult stretch of trail or if she gets too tired, you need be ready to carry her.

Canine first aid kit

Dangers to your dog are numerous on a long hike. They include fatigue, hypothermia, and heat stroke. Check the pads of your dog’s feet for wounds from thorns or sharp rocks, especially if she’s stopping to lick or gnaw at her paws. He could easily get stung by a bee, bit by a rattlesnake, attacked by a predator, rip a pad, break a bone, eat something toxic, eat something infected, fall, drown, or get lost. He could acquire Lymes disease, leptospirosis, giardia, salmon poisoning, heartworm, or an allergic reaction to poison oak. Although all of these things could happen to you, he may not be thinking clearly about these dangers when he smells that rotten fish carcass or chases that coyote up the trail. You better have a canine first aid kit when hiking.

Treats and food

Bring lunch for your dog and high-value treats to reward them or just lure them back to you. Though higher quality dog food is more expensive by the pound, you will actually save weight and give your dog more nutrition if you can feed a high quality food on the trail.

Booties

If you’re going to take your dog on a long hike or backpacking trip, there are a lot of extras to think about. Will the weather be too hot? What kinds of dog hiking gear will you need? Hike early in the morning or later in the evenings and your babies can enjoy a great fun during these suitable periods of time. Dog booties can help when your puppy is injured, walking on rough terrain and etc.

Insect repellent

If you’re being around with bugs, I bet your dog is being bitten too. So it is necessary to prepare insect repellent.

Leash and collar

Have a leash ready. Beyond the fact that many hiking areas require dogs be leashed, you need to be able to control your dog around other hikers, other dogs or wild animals. Even on trails where dogs are acceptable with leash off, it is good to have a leash with you in case of an emergency.

Water and water bowl

Bring lots of water is necessary. Make sure you have enough water for your dog while hiking since there may not be water sources along the trail.

Assessment

Having dog with us affects where we can hike, what time of day I can hike. As for where to hike, your options will be more limited. A moderate, knee-deep creek crossing for a human may be a significant swim for a dog. And it is dangerous when the dog isn’t a strong enough to swim. If you’re going somewhere you’ve never hiked before, certain obstacles may prevent you hiking with your dog and you need to leave dog at home.

You should remember to consider your dog’s overall fitness level when making this assessment. Be honest about your dog’s abilities, then do your homework and make sure you’re headed somewhere that is within those abilities.

Know About Camera for Outdoor Expedition

There are still a lot of things that we don’t know about the nature, so the outdoor expedition is important for today’s study, and the necessary part of this is a good camera.

Nowadays, the development of science and technology is growing up, and the digital camera has already become a essential part of our daily life. Besides, for the science field, the digital camera is the most important part which is used to record something, especially some new discovery so that the scientists can study and work on to make people’s life better. Photographs are a wonderful way to record some memories and some parts of the world that are still remote and beautiful for the outdoor expedition.

So today’s article is going to tell you something about  choose camera for expedition and what you need to do so that it can be a safe camera for expedition.

Choose Camera For Outdoor Expedition

The first and the most important thing for a expedition is not put it off or cut corners to saveup for a camera, but do the expedition. First you need go out and do whatever you have to do, an then take pictures with the camera that you have.

About the camera, there are three main options, each with pros and cons, of course you can buy a new one, if you have enough money, then you can also buy a second hand, which is also a good option, or you can even get your hands on an old family or friends camera, which is great as long as you make no promises about it’s condition.

Here are three types of cameras for you to reference today. The first is Point-and-Shoot which is a kind of mall, light and cheap camera, and in recent years, the quality has improved a lot. For an outdoor expedition, this kind of camera is a good beginning. The second is Bridge Cameras which is a kind of bridge as what it’s named between small, light point-and-shoots and bigger, heaver DSLRs. It can provide a lot of user control such as shutter speed and aperture with one fixed, but versatile lens. The third is Full DSLR camera which is called digital single lens reflex will cost a lot on lenses. Those lenses are the added expense beyond camera, and the better the lenses are, the more expensive they are.

outdoor expedition

Things You Need to Care For Cameras on Expedition

The first thing you need to pay attention to is the batteries of the cameras you use for outdoor expedition. The battery is the heart of a camera and when you do a remote area expedition, charging electronics will be limited, which means that you need enough batteries. Although there are specialist batteries for many cameras, a various of batteries can be bought on the market, such as AA batteries, AA compatible battery pack, Powerpacks, solar chargers. What’s more, the temperature is another big problem for using camera, because in very cold conditions, batteries will not last quite as long as in the room temp.

The second is to keep cameras dry for outdoor expedition, especially in the rainforest, which is a big challenge.

  • Do not bring camera equipment in and out of any air-conditioned rooms.
  • Do not take off sashes of silica gel in each of your camera bags.

Do not forget the rain covers such as plastic sleeves or storm jackets.

outdoor expedition

The third thing is you need avoid your camera being close to dust and sand. If it is necessary for you to bring camera to a desert, there are three thing may make you happy: a dust blower, wet wipes and a silicone shell.

outdoor expedition

The forth thing is to protect your camera from the clash like the bag which takes your camera or lenses will be thrown onto the roof of a van. Tuppaware is a kind of solution to that problem and it is very cheap, strong and comes in a variety of sizes that you are able to find the certain one for your kit.

outdoor expedition

The fifth thing is much more important for your outdoor expedition, it is called tripods which is light, small and not too expensive. But if you really the tripods will take too much space in your bag, you can use camera beanbags, camera pods and monopods to replace the tripods so that you can save your space in your bag.

The sixth is that if you don’t have enough money or you have further down the budget for a new camera, the second hand camera will be a good option. When you use the second hand, you will worry slightly less if something goes wrong.

The last but not the least thing you need to pay attention to is you can not just use a tiny quarter-inch viewfinder to experience this world. You need use your eyes and your heart to feel the beauty of this unique world.

Things are changing right now, and thisworld is also changing. There are too many things will change in a second, so we really need a good camera to record those moment which will disappear just in a second. Photography is just one way you can memorize those unforgettable moment and the beautiful corner of this world, but it is not the only way to do that, the most important part is using your eye to see, your heart to feel and your brain to memorize, this is the most important thing, not just use the tiny quarter-inch viewfinder to see the beauty.

When you reach one place where is beautiful, slow down and stop for a moment, use your heart to feel the beauty, the quiet moment and the myth of nature. When you are on outdoor expedition, bring your camera and don’t forget the eye and heart.

Best ways of preventing injuries when handling heavy Industrial materials

Actually, during the process of pipe and tube fabricating, there are so many risks that fabricators ignores. And today we’ll talk about how to keep ourselves safety.

Introduction

In the past 25 years, people’s safety situation has developed deeply especially in manufacturing facilities. However, to our surprise, there are still a number of problems to be solved,for example, although those hot rolled round pipe are easy to move up, if you don’t use the correct and appropriate controls, it will still be dangerous. Pipe and tube facilities has been the symbol of the fabricating world on some extents, but it is obvious that there are still some big problems. Now let’s have a look to some examples and scenarios of tube and pipe about those companies how to solve these problems and attempt to tackle these varieties of safety problems.

Awareness of the danger of press brakes and stamping presses during the past decades, and people have develop deeply. Nowadays, the FORTUNE 500 companies pay more attention to the low workers’ compensation insurance modification. If you are more care about this point, you will have a better condition to win. Besides,  the technological improvements in the safeguarding devices and Mechanical Power Presses based on the Occupational Safety and Health Administration’s enforcement of CPL 2-1.24 National Emphasis Program are also the important considering points.

But as in the tube and pipe industry, it is different from that. Operational hazards similar to those in general fabricating  can be found in the tube and hot rolled round pipe pipe. But safeguarding devices are not be used or be ignored. For those who work in the producing or manufacturing to the tube and pipe, it is not obvious to that that danger. The operators are required to stay with those workers so they are in the same dangerous, based on company-established administrative safety measures and their own skills to prevent injury.

Unlike flat metal, tube and pipe is round and they don’t have burrs and sharp edges. When straight, their shapes allow gravity available to move them to the shop. Unfortunately, these parts are tough to stack, if it could, it will became a big problem of handling and storage.

Tube and pipe operators are inclined to work for a long time. As in any manufacturing scenario, safety enhancement is an important part to less the danger than the safe standard. Now I will introduce some information about how to reduce the operator risks with and the the risk analysis.  Also an investment in implementing the right safeguarding devices and improvements to the manufacturing processes.

  Scenario No. 1: The Gravity-fed Pipe Handling System

In this production facility, flat steel comes off a coil and is formed into pipe. It provide varieties of sizes, and the biggest is 40in,  in diameter trimmed into 60-ft. lengths and having a wall thickness of 0.625 in. It’s big and heavy stuff.

The black ERW round pipe production process is enclosed by mechanical barriers and fencing. If access, you only go through the closed door. For the most part, it has a protection to reduce the risk. But The pipe handling situation in the inspection area is another situation. It is a very dangerous process that two people is in a system that one rise up his hand, and other press the button to move the black ERW round pipe pipe.

If one just want to wave away a fly, and then press the button. Oh, it will be a big problem. Unfortunately, the gravity-fed system doesn’t come with instantaneous stop.

The best way for improvement is to make the inspection process be automatic. However, version system is expensive are less intuitive than our eyes.

To allow operators continue to working and reduce the risk, the company should implement the combination of engineered and monitored administrative. First, safety laser scanners should be put in place to make sure the area is clear what they are doing before the other one go into the next station. Second, we are add the other operating station so that we can seek what the other one is doing so as to reduce the risk.

Scenario No. 2: The Improperly Guarded Tube Bending Cell

Behind the horizontal tube bender, there is a safety laser scanner that when workers are in the working area, electronic floor mat will stop.

But it has been reprogrammed and the operator implies that it is the only way he can hold the part in place while clamping.  Once the tube is clamped, he then moves out of the working area and initiates the bending process. At the beginning, it just for reduce the risk.

Ironically, the most useful feature for the safety laser scanner is easy to reprogrammed to adjust the varieties of working area.

The key point of protecting workers is that all metal is just admired to adjust their fabricating activity. A safeguard should be easier to work than around.

Staying Productive and Safe

Compared with 10 years ago, the effect of safeguard to manufacturing process has decreased. Technical advancement and lean manufacturing process are beneficial to our safety and today’s manufactures can gain those to make operation safer ,effective and productive.

WELCOME

Welcome to the School of Expeditionary Sciences of the Fortune Bay Expedition Team!

Looking for the team’s public homepage?

The School of Expeditionary Sciences provides courses, training and information on a variety of subjects.  They include outdoor skills, leadership, safety, search and rescue, wilderness medicine, expedition planning/execution and much more.  The school combines online content with real world courses, trips, expeditions and training.

To access the information on this site, individuals must be a Guild or Professional Member of the Fortune Bay Expedition Team or enroll as a student.  We are presently not accepting new students but we are welcoming new Guild Members.  Follow the link to learn more about becoming a Guild Member of the Fortune Bay Expedition Team,